How to Remove and also Change a Bathtub.
How to Remove and also Change a Bathtub.
Blog Article
Right here in the next paragraph you can discover a good deal of quality help and advice in regards to How to Install a Bathtub.
Setting up a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the task can move rapidly; if you have to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your shower room if you have currently acquired a new tub and don't need to change the arrangement of your previous water supply pipes.
Your devices and also material list need to consist of the following:
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for setting. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level checks out degree.
To set up taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water and also examine all joints as well as new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally inspect the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing complications with wetness and possible leakages to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is suggested to fit the floor tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article on Tools You Need to Install a New Bathtub through a good friend on a different domain. Are you aware of another person who is enthusiastic about How to Install a Bathtub Yourself? Feel free to share it. We recognize the value of reading our article about How to Install a Bathtub.
Go Deal Report this page